Description & Primary Use
The Rag Company Ultra Air Blaster Plus+ is a hybrid detailing tool that uses compressed air + liquid (cleaner) to create a vortex / spray that helps lift and remove dirt from surfaces. The idea is to combine the mechanical force of air with a cleaning solution (typically a water-based chemical) so you can “blast” grime, dust, residues, etc., off surfaces (especially interior surfaces) with less manual scrubbing. It’s especially marketed for interior detailing: carpets, upholstery, plastics, trim, crevices, door jambs, etc. It comes with two interchangeable trumpet (nozzle) tips: a “standard” trumpet and a “bristle” trumpet (i.e. with brush bristles) to aid in agitation of stubborn dirt. It is trigger operated (i.e. there is a trigger to control flow) and is constructed of metal to give durability. The “Plus+” version’s distinguishing feature is this liquid + air mixing capability. (In contrast, some air blasters are air-only.)
In short: it’s a detailing tool to deep clean interior surfaces more efficiently by using air + cleaner to dislodge grime, rather than relying solely on manual scrubbing or wiping.
Specifications
| Parameter | Value / Range |
|---|
| Free rotation speed (vortex) | 8,000 – 12,000 RPM |
| Air consumption | 120 L/min to 200 L/min |
| Liquid consumption | 3.0 – 3.7 L/hour |
| Input pressure | 6 – 8 bar (≈ 87 – 116 psi) |
| Fitting / connection | Standard US connection / ¼-inch fitting |
| Air outlet / nozzle design | Uses a 360° tube so it can pull liquid regardless of angle, enabling use at non-upright positions. |
| Materials / build | Metal body, durable construction, includes two nozzle attachments (standard + bristle), lid / storage cap, ¼" NPT fitting (or adaptor) included. |
| Weight / physical | I did not find a confirmed weight beyond user listings, but Amazon listings note item weight ~ 2.33 lb (for the Plus version) |
Best Practices / Usage Tips (and Caveats)
From manufacturer guidance, user reviews, and detailing-forum commentary, here are best practices, do’s & don’ts, and tips to make the tool work well:
Adequate Air Supply is Critical
To run this tool effectively, you need a compressor that can deliver the required flow (e.g. 4 cfm or higher) at stable pressure. Several users warn that weaker compressors struggle to maintain pressure and the tool underperforms.
The manufacturer (for its version 2) recommends using a minimum 20-gallon compressor to avoid pressure drop issues.
Hose diameter, fittings, and pressure drops along the line matter. Use low-restriction hoses and quality fittings.
Proper Pressure Setting
Input pressure ranges around 6–8 bar (≈ 90 – 116 psi) are recommended. Operating outside that range may reduce effectiveness, or cause excessive overspray/mist.
Some users reported that if the compressor’s tool pressure drops when the trigger is pulled, performance suffers. One user noted their pressure dropped from 90 psi to ~60 psi under use.
Use Only Water-Based / Compatible Cleaners
Do not use with silicone-based products or heavy solvent/durables that might gum up the mechanism or cause damage.
Stick with good APCs (all-purpose cleaners), interior cleaners, or other detailing solutions that are safe for the surfaces you are treating.
Start Slowly / Dial in Liquid-to-Air Ratio
Because the tool mixes air + liquid, you’ll want to fine-tune how much liquid is injected relative to airflow. For delicate surfaces, lean more on air; for tougher dirt, increase liquid. Some user reviews mention the value of a mixing valve.
You may run the tool without liquid (i.e. pure air blasting) for dust/dry cleaning, then switch on liquid when needed. Some users suggest toggling between air-only and air + liquid during a pass (e.g. first blow dust, then spray, then blow).
Use Appropriate Nozzle / Trumpet Attachments
Use the bristle trumpet when you need agitation (e.g. on fabric, carpets with embedded dirt) to help scrub loosened grime as it's blasted.
Use the standard trumpet when lighter, broad spraying is sufficient or on smoother surfaces.
Work in Overlapping Passes, Moderate Distance
Don’t get too close with the nozzle — allow the vortex / spray to lift the grime.
Work methodically in sections (e.g. one door panel, one seat area) so you don’t oversaturate or miss spots.
Ventilation & Respiratory Protection
Because the tool atomizes liquids and produces a fine mist, it can cause airborne particles / fumes. In closed spaces or extended use, use a mask or respirator. One user reported sinus issues when not wearing protection.
Pre-Vacuum or Pre-Clean Where Necessary
For large debris, leaves, or heavy soil, vacuum or remove big contaminants first to avoid clogging or overworking the tool. Many detailers still vacuum before using an air blaster. (This is a general detailing best practice, not specific to this tool.)
Also, ensure surfaces are wet enough (if using liquid) so that the spray doesn’t just bounce or evaporate.
Maintain the Tool Carefully
Keep the internal passages clean and clear (liquid, air, trumpet) to avoid clogging.
Inspect o-rings, seals, and replace any worn parts.
Ensure bearings, if any, remain smooth. Some newer versions (v2) allow easier bearing replacement.
Avoid letting cleaner sit in the lines for long periods (flush/clean after use).
Protect from corrosive chemicals or harsh solvents that could degrade the metal or seals.
Watch for Overuse / Diminished Performance
Some users report that after months, the spinning mechanism may stick or lose speed.
If the unit seems to underperform (less blast, slower spin), check for leaks, clogged passages, or dropped compressor pressure.
